《操作系统》的实验代码。
Du kannst nicht mehr als 25 Themen auswählen Themen müssen entweder mit einem Buchstaben oder einer Ziffer beginnen. Sie können Bindestriche („-“) enthalten und bis zu 35 Zeichen lang sein.
 
 
 
 
 

84 Zeilen
3.8 KiB

#ifndef __KERN_DRIVER_KBDREG_H__
#define __KERN_DRIVER_KBDREG_H__
// Special keycodes
#define KEY_HOME 0xE0
#define KEY_END 0xE1
#define KEY_UP 0xE2
#define KEY_DN 0xE3
#define KEY_LF 0xE4
#define KEY_RT 0xE5
#define KEY_PGUP 0xE6
#define KEY_PGDN 0xE7
#define KEY_INS 0xE8
#define KEY_DEL 0xE9
/* This is i8042reg.h + kbdreg.h from NetBSD. */
#define KBSTATP 0x64 // kbd controller status port(I)
#define KBS_DIB 0x01 // kbd data in buffer
#define KBS_IBF 0x02 // kbd input buffer low
#define KBS_WARM 0x04 // kbd input buffer low
#define BS_OCMD 0x08 // kbd output buffer has command
#define KBS_NOSEC 0x10 // kbd security lock not engaged
#define KBS_TERR 0x20 // kbd transmission error
#define KBS_RERR 0x40 // kbd receive error
#define KBS_PERR 0x80 // kbd parity error
#define KBCMDP 0x64 // kbd controller port(O)
#define KBC_RAMREAD 0x20 // read from RAM
#define KBC_RAMWRITE 0x60 // write to RAM
#define KBC_AUXDISABLE 0xa7 // disable auxiliary port
#define KBC_AUXENABLE 0xa8 // enable auxiliary port
#define KBC_AUXTEST 0xa9 // test auxiliary port
#define KBC_KBDECHO 0xd2 // echo to keyboard port
#define KBC_AUXECHO 0xd3 // echo to auxiliary port
#define KBC_AUXWRITE 0xd4 // write to auxiliary port
#define KBC_SELFTEST 0xaa // start self-test
#define KBC_KBDTEST 0xab // test keyboard port
#define KBC_KBDDISABLE 0xad // disable keyboard port
#define KBC_KBDENABLE 0xae // enable keyboard port
#define KBC_PULSE0 0xfe // pulse output bit 0
#define KBC_PULSE1 0xfd // pulse output bit 1
#define KBC_PULSE2 0xfb // pulse output bit 2
#define KBC_PULSE3 0xf7 // pulse output bit 3
#define KBDATAP 0x60 // kbd data port(I)
#define KBOUTP 0x60 // kbd data port(O)
#define K_RDCMDBYTE 0x20
#define K_LDCMDBYTE 0x60
#define KC8_TRANS 0x40 // convert to old scan codes
#define KC8_MDISABLE 0x20 // disable mouse
#define KC8_KDISABLE 0x10 // disable keyboard
#define KC8_IGNSEC 0x08 // ignore security lock
#define KC8_CPU 0x04 // exit from protected mode reset
#define KC8_MENABLE 0x02 // enable mouse interrupt
#define KC8_KENABLE 0x01 // enable keyboard interrupt
#define CMDBYTE (KC8_TRANS|KC8_CPU|KC8_MENABLE|KC8_KENABLE)
/* keyboard commands */
#define KBC_RESET 0xFF // reset the keyboard
#define KBC_RESEND 0xFE // request the keyboard resend the last byte
#define KBC_SETDEFAULT 0xF6 // resets keyboard to its power-on defaults
#define KBC_DISABLE 0xF5 // as per KBC_SETDEFAULT, but also disable key scanning
#define KBC_ENABLE 0xF4 // enable key scanning
#define KBC_TYPEMATIC 0xF3 // set typematic rate and delay
#define KBC_SETTABLE 0xF0 // set scancode translation table
#define KBC_MODEIND 0xED // set mode indicators(i.e. LEDs)
#define KBC_ECHO 0xEE // request an echo from the keyboard
/* keyboard responses */
#define KBR_EXTENDED 0xE0 // extended key sequence
#define KBR_RESEND 0xFE // needs resend of command
#define KBR_ACK 0xFA // received a valid command
#define KBR_OVERRUN 0x00 // flooded
#define KBR_FAILURE 0xFD // diagnosic failure
#define KBR_BREAK 0xF0 // break code prefix - sent on key release
#define KBR_RSTDONE 0xAA // reset complete
#define KBR_ECHO 0xEE // echo response
#endif /* !__KERN_DRIVER_KBDREG_H__ */